CANTEX INTERSECTS 23.5 METRES OF 8.34% LEAD-ZINC AT THE MAIN ZONE INCLUDING 2.5 METRE ZONES OF UP TO 24.72% LEAD-ZINC AND 85 G/T SILVER ON ITS 100% OWNED NORTH RACKLA PROJECT, YUKON
KELOWNA, BC, Jan. 12, 2023 /CNW/ - Cantex Mine Development Corp. (TSXV: CD) (OTCQB: CTXDF) (the "Company") is pleased to provide an update on drilling of the Main Zone at its 100-percent-owned 14,077 hectare North Rackla claim block in the Yukon.
Figure 1: Main Zone Drilling (CNW Group/Cantex Mine Development Corp.)
Figure 2: Cross Section Through MZ52 and MZ52A (CNW Group/Cantex Mine Development Corp.)
Figure 3: Cross Section Through MZ53A (CNW Group/Cantex Mine Development Corp.)
Figure 4: Cross Section Through MZ54A (CNW Group/Cantex Mine Development Corp.)
Drilling confirms strike extension of mineralization to northeast along Main Zone
Cantex is pleased to report results from a further five drill holes from its 2022 drill program at the Main Zone of the North Rackla project. These holes, drilled in the Discovery Sector, extended the Main Zone mineralization 150 metres further to the northeast than had been previously identified, bringing the Main Zone strike length to 2,300 metres.
The results from the five holes are presented in Table 1. Figure 1 shows the locations of the drill pads discussed in this release.
Hole YKDD22-246 was drilled from pad MZ52, a 50 metre step out from the previous year's drilling, and intersected 23.5 metres of 20.46 g/t silver and 8.34% combined lead and zinc. Within this intercept there were two higher grade zones, both 2.5 metres long. The first contained 44.68 g/t silver ad 19.06% combined lead and zinc. The second contained 85.32 g/t silver and 24.72% combined lead and zinc. A cross section of these holes is shown in Figure 2.
Holes YKDD22-250, YKDD22-255 and YKDD22-257 were drilled from pad MZ53A, a 100 metre step out from the drilling in 2021. Figure 3 shows a cross section through these holes.
Hole YKDD22-254 was drilled from pad MZ54A, a 150 metre step out from the drilling in 2021. It intersected several zones of mineralization including a 12.7 metre zone within which 1.5 metres contained 75.33 g/t silver and 24.21% combined lead and zinc. A cross section through these holes is presented in Figure 4.
Table 1. Significant results from Discovery Sector
Pad
Dip
Hole
From
To
Interval
Silver
Lead
Zinc
Lead + Zinc
Cop- per
Manga- nese
(m)
(m)
(m)
ppm
( %)
( %)
( %)
( %)
( %)
MZ52
-65
YKDD22-246
49.00
52.00
3.00
4.07
0.68
1.52
2.20
0.00
0.31
55.00
78.50
23.50
20.46
3.30
5.04
8.34
0.01
4.53
Including
57.50
60.00
2.50
44.68
3.39
15.67
19.06
0.03
4.62
And
73.50
76.00
2.50
85.32
13.79
10.93
24.72
0.04
3.66
90.00
91.00
1.00
7.19
1.88
0.53
2.41
0.01
0.98
MZ53A
-55
YKDD22-250
25.00
25.50
0.50
15.35
0.32
3.87
4.19
0.04
0.13
156.00
166.00
10.00
38.60
6.39
7.60
13.99
0.06
2.86
180.00
183.50
3.50
52.76
7.97
4.62
12.59
0.13
2.22
194.35
195.20
0.85
19.65
4.26
2.84
7.10
0.08
0.47
207.15
207.65
0.50
15.50
2.68
3.75
6.43
0.02
3.01
210.50
211.10
0.60
4.60
0.55
1.46
2.01
0.01
1.22
-71
YKDD22-255
201.00
212.00
11.00
11.91
0.56
2.86
3.42
0.07
1.48
Including
201.00
204.00
3.00
36.27
1.45
5.38
6.83
0.22
1.70
278.70
281.50
2.80
4.59
0.69
1.97
2.66
0.01
1.28
-75
YKDD22-257
220.20
223.00
2.80
62.66
7.06
3.45
10.51
0.18
1.25
246.10
247.60
1.50
1.95
0.06
1.08
1.14
0.01
0.95
MZ54A
-55
YKDD22-254
150.30
163.00
12.70
24.25
1.04
3.20
4.24
0.08
2.63
Including
150.30
151.80
1.50
75.33
4.59
19.62
24.21
0.06
2.71
169.00
169.50
0.50
14.00
3.22
6.23
9.45
0.01
4.08
173.00
173.50
0.50
25.90
1.48
8.07
9.55
0.03
3.66
178.50
182.50
4.00
34.21
6.47
5.12
11.59
0.12
3.06
Including
179.00
180.50
1.50
69.60
13.96
9.97
23.93
0.16
3.29
220.00
221.00
1.00
5.49
0.58
3.55
4.13
0.00
1.02
During 2022 the Company drilled 13,187 metres in 62 holes. Results are awaited from 46 holes and will be released when received.
Sample Preparation
The drill holes reported in this press release were drilled using HQ (63.5mm) diamond drill bits. The core was logged, marked up for sampling and then divided into equal halves using a diamond saw on site. One half of the core was left in the original core box. The other half was sampled and placed into sealed bags which were in turn placed into larger bags closed with security seals prior to being transported to CF Mineral Research Ltd. in Kelowna, BC.
At CF Minerals the drill core was dried prior to crushing to -10 mesh. The samples, which averaged over 3kg, were then mixed prior to splitting off 800g. The 800g splits were pulverized to -200 mesh and a 250g split was sent for assay. Quality control procedures included running a barren sand sample through both the crusher and pulveriser between each sample to ensure no inter-sample contamination occurred. Silica blanks were inserted along with certified reference samples. These quality control samples were each inserted approximately every 20 samples.
ALS Chemex in Vancouver assayed the samples using a four-acid digestion with an ICP-MS finish. The 48 element ME-MS61 technique was used to provide a geochemical signature of the mineralization. Where lead or zinc values exceeded one percent the Pb-OG62 or Zn-OG62 techniques were used. These have upper limits of 20% lead and 30% zinc respectively. Samples with lead and zinc values over these limits were then analyzed by titration methods Pb-VOL70 and Zn-VOL50. Where silver samples exceeded 100 g/t the Ag-OG62 technique was used which has an upper limit of 1,500 g/t. The over limit analyses contributed to delays in receiving final assay results.
The technical information and results reported here have been reviewed by Mr. Chad Ulansky P.Geol., a Qualified Person under National Instrument 43-101, who is responsible for the technical content of this release.
Signed,
Charles Fipke
Charles Fipke, CM Chairman
Neither TSX Venture Exchange nor its Regulation Services Provider (as that term is defined in the policies of the TSX Venture Exchange) accepts responsibility for the adequacy or accuracy of this release. Information set forth in this news release includes forward-looking statements under applicable securities laws. Forward-looking statements are statements that relate to future, not past, events. In this context, forward-looking statements often address expected future business and financial performance, and often contain words such as "anticipate", "believe", "plan", "estimate", "expect", and "intend", statements that an action or event "may", "might", "could", "should", or "will" be taken or occur, or other similar expressions. All statements, other than statements of historical fact, included herein are forward-looking statements. By their nature, forward-looking statements involve known and unknown risks, uncertainties and other factors which may cause the actual results, performance or achievements, or other future events, to be materially different from any future results, performance or achievements expressed or implied by such forward-looking statements. Such factors include, among others, risks identified in the management discussion and analysis section of the Company's interim and most recent annual financial statements or other reports and filings with Canadian securities regulators. Forward looking statements are made based on management's beliefs, estimates and opinions on the date that statements are made and the respective companies undertake no obligation to update forward-looking statements if these beliefs, estimates and opinions or other circumstances should change, except as required by applicable securities laws. Investors are cautioned against attributing undue certainty to forward-looking statements.
SOURCE Cantex Mine Development Corp.
Cantex Mine Development Corp, Tel: +1-250-860-8582; Email: [email protected]
Share this article